Quick Answer: Underwater landslides are sudden downslope movements of seafloor sediment, often set off by earthquakes, storms, or rapid sediment buildup. Scientists have now recorded them as they happen, which gives researchers direct evidence of how these flows start and move. They matter because they can snap cables and damage pipelines.
For decades, researchers have inferred what happens on the seafloor during a slide from broken cables, displaced sediment, and sonar snapshots taken after the fact. According to a Moneycontrol report, scientists have now captured underwater landslides while they are actually unfolding. That shifts the question from "what probably happened?" to "what exactly happened, second by second?" Here's why that matters for anyone who depends on the ocean floor.
Why Underwater Landslides Are So Hard to Observe
Most of the seafloor sits in darkness, under thousands of metres of water, and out of view. A landslide there leaves no splash and no sound you can hear from the surface. You usually find out only after something breaks.
That's why the field has relied on indirect evidence. Researchers map scars and deposits with multibeam echosounders, which sweep the seabed with sonar to build detailed bathymetric maps. They compare maps taken before and after an event. The problem is that a map shows where material ended up, not how it got there or how fast it moved.
Real-time capture closes that gap. A system that is already sitting on the seafloor when a slope fails can record the event as it happens. The new study, as the report describes it, is the first time this has been done.
How Underwater Landslides Form
Submarine slopes are always under stress. Gravity pulls sediment downhill, and the sediment's own strength holds it in place. A landslide happens when the balance tips, usually because something adds stress or reduces strength.
The most common mechanisms are:
- Sediment loading: Fast-accumulating sediment, such as river deltas during floods, piles up on steep slopes faster than it can consolidate.
- Seismic shaking: Earthquakes shake the slope and can liquefy loose, water-saturated sand.
- Gas hydrate destabilisation: Methane hydrates that cement sediment can break down when temperature or pressure changes, weakening the slope.
- Storm waves and currents: Large waves and strong bottom currents can erode the toe of a slope and trigger failure.
Once a slide starts, it often transforms. The sediment mixes with water and becomes a dense, fast-moving flow called a turbidity current. This is the part that matters most for infrastructure, because turbidity currents can travel for hundreds of kilometres along the seafloor.
The 1929 Grand Banks Event Showed the Stakes
The clearest historical warning came in 1929. A magnitude 7.2 earthquake struck the continental slope off Newfoundland, on the Grand Banks. It triggered a submarine landslide that set off a turbidity current, and that current broke a series of transatlantic telegraph cables in sequence. Engineers and geologists later used the timing of each cable break to estimate the current's speed, which reached tens of kilometres per hour in places.
That's a counter-intuitive lesson. Many people assume the seafloor is stable and that the danger to cables comes only from ships dragging anchors. The Grand Banks event shows that a slope failing hundreds of kilometres away can break cables that never touched the slide itself.
Here's where the story gets more interesting: the cables were acting as accidental sensors. Their failure times traced the flow's path, which is exactly the kind of data modern observatories now try to collect on purpose.
Why Ocean Infrastructure Is at Risk
Today's seafloor carries a dense network of fibre-optic internet cables, power interconnectors, and oil and gas pipelines. A large share of global internet traffic moves through undersea cables. When one breaks, repairs can take weeks, and ships must be scheduled to find the fault and splice it.
The risk isn't evenly spread. Cables are most exposed where they cross steep canyons, continental slopes, and river-fed deltas, because those are the places where sediment is most likely to fail. Routing decisions made decades ago may not reflect current understanding of where slides are most likely.
Here's the practical implication. When you assess route risk for a cable or pipeline, you need to know slope gradient, sediment type, and seismic exposure. A route that looks safe on a bathymetric chart can still cross a slope that is primed to fail.
Comparing Common Triggers and Monitoring Tools
Different triggers call for different monitoring approaches. The table below compares the main triggers and the tools typically used to watch for them.
| Trigger | Typical setting | Main warning signal | Common monitoring tool |
|---|---|---|---|
| Earthquake shaking | Active margins and subduction zones | Seismic events near slopes | Seafloor seismometers, cabled observatories |
| Sediment loading | River deltas and canyon heads | Rising sediment flux, steepening slopes | Multibeam bathymetry, repeat surveys |
| Gas hydrate breakdown | Deep continental margins | Temperature and pressure shifts | Temperature probes, pore-pressure sensors |
| Storm and current erosion | Shelf edges and canyon walls | Strong bottom currents and wave energy | Acoustic Doppler current profilers |
No single tool covers every trigger. A seismometer won't tell you about a slope loaded with sediment, and a bathymetric survey won't tell you when shaking started. Most serious monitoring combines several.
That said, there's a real trade-off. Cabled observatories such as Ocean Networks Canada's NEPTUNE network provide continuous power and data, but they are expensive and cover only specific sites. Autonomous instruments are cheaper and more flexible, but they can be lost in a slide or run out of power before the next event.
What Real-Time Capture Changes
Direct observation changes three things. First, it tests models. Many numerical landslide models have relied on assumptions about how fast flows travel and how much material they carry. Real measurements let researchers check those assumptions.
Second, it sharpens hazard maps. A hazard map built on observed flow behaviour is more useful to a cable operator than one built on guesswork.
Third, it improves early warning. If a slope failure can be detected in its first moments, operators have a chance to respond. The difficulty is that a turbidity current can outrun a warning signal over long distances. That's a limit worth keeping in mind.
Most people stop here, but the next question is the one that matters for operators: what do you do with this information? The answer depends on your role, and we'll come back to it in the closing section.
Frequently Asked Questions
What is an underwater landslide?
An underwater landslide is the downslope movement of sediment on the seafloor, usually on a continental slope or canyon wall. It can be a slow slump or a fast-moving flow called a turbidity current. Because it happens out of sight, it often goes unnoticed until it damages something on the seabed.
How do underwater landslides form?
They form when the stress on a sediment slope exceeds its strength. Common causes include rapid sediment buildup, earthquake shaking, storm erosion, and the breakdown of gas hydrates. Often a combination of factors triggers the failure.
Why do underwater landslides threaten undersea cables?
A turbidity current from a slide can travel for hundreds of kilometres and carry enough force to break cables along its path. The 1929 Grand Banks event showed that cables can fail far from the original slide. Routing cables away from steep, sediment-rich slopes reduces that exposure.
Protect Your Routes by Checking the Slope
The main takeaway is simple: underwater landslides are not just a geology story. They can reach cables and pipelines far from where they start, so slope risk belongs in route planning. If you manage a subsea asset, pull the bathymetry for your route this week and mark every section where the gradient is steep and sediment is thick. Share that map with the person who will be deciding where the next cable goes.